Vetää ulos lommoja haulikon ilmanvaihtoripoista vain minuuteissa. Helppo kiinnittää ja nopea käyttää. Messinkinen silta ei jätä jälkiä ripojen päälle; teräsleuat säätyvät itsestään.
TEKNISET TIEDOT: Silta; Koneistettu messinki 3" (7,6 cm) pitkä, ¼" (6,3 mm) paksu. Leuat; Koneistettu, karkaistu teräs 1½" (3,8 cm) pitkä, ½" (12,7 mm) leveä leveimmästä kohdasta.
Lisää...
Asiakasarviot: MURRAYS VENT RIB TOOL
Arvioiden lukumäärä: 5
Arvostelut brownells.com sivustolla: 5
Arvioiden keskiarvo: 5
Cheaper than a new rib!(9.3.2010)
I used this tool to remove two severe dents in the rib of my Ruger O/U. I was very tentative at first, but once I got used to the pressure it worked like a charm. You do have to slightly over tighten to ensure the dent is removed. A heavy hand could convert a dent to a hump. Patience and checking with a steel rule will keep you in a great place.
Handy little tool(10.7.2012)
Neatest thing since a pocket on a shirt. Pulls dinged ribs right up. Like the other reviewer noted, you do need to pull it up a little higher than flat and check it with a flat edge, but works like it's supposed to.
works graet, easy to use (1.12.2014)
I have used this tool about 10 times and it has worked great, easy and fast, One great tool.
Better than a gunsmith (13.6.2015)
Simple to use tool that works! I used this on my baby a Perazzi, did not want to ship the gun off. Prior dent is not noticeable after a bit of cold blue touch up. Use with caution, adjust, measure and repeat.
Christmas surprise (26.12.2016)
Unsightly crimp in my over under vent rib near the mid sight. Took it to three gunsmiths. Two refused to fix it and one wanted $150 and to remove my mid sight mark. I said no and lived with the crimp for a year. Then this Christmas my wife ordered the Murray vent rib tool from Brownells.. Was just going to test the fit of the tool and realized I could fix it. Took me seconds and my barrell was good as new. Every shotgunner with vent ribs needs this tool.
Tuotenro: 563100000 MURRAYS VENT RIB TOOL Valmistajan tuotenumero: NONE Vetää ulos lommoja haulikon ilmanvaihtoripoista vain minuuteissa. Helppo kiinnittää ja nopea käyttää. Messinkinen silta ei jätä jälkiä ripojen päälle; teräsleuat säätyvät itsestään.
124.9EUR14124,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Vetää ulos lommoja haulikon ilmanvaihtoripoista vain minuuteissa. Helppo kiinnittää ja nopea käyttää. Messinkinen silta ei jätä jälkiä ripojen päälle; teräsleuat säätyvät itsestään.
TEKNISET TIEDOT: Silta; Koneistettu messinki 3" (7,6 cm) pitkä, ¼" (6,3 mm) paksu. Leuat; Koneistettu, karkaistu teräs 1½" (3,8 cm) pitkä, ½" (12,7 mm) leveä leveimmästä kohdasta.
Lisää...
Asiakasarviot: MURRAYS VENT RIB TOOL
Arvioiden lukumäärä: 5
Arvostelut brownells.com sivustolla: 5
Arvioiden keskiarvo: 5
Cheaper than a new rib!(9.3.2010)
I used this tool to remove two severe dents in the rib of my Ruger O/U. I was very tentative at first, but once I got used to the pressure it worked like a charm. You do have to slightly over tighten to ensure the dent is removed. A heavy hand could convert a dent to a hump. Patience and checking with a steel rule will keep you in a great place.
Handy little tool(10.7.2012)
Neatest thing since a pocket on a shirt. Pulls dinged ribs right up. Like the other reviewer noted, you do need to pull it up a little higher than flat and check it with a flat edge, but works like it's supposed to.
works graet, easy to use (1.12.2014)
I have used this tool about 10 times and it has worked great, easy and fast, One great tool.
Better than a gunsmith (13.6.2015)
Simple to use tool that works! I used this on my baby a Perazzi, did not want to ship the gun off. Prior dent is not noticeable after a bit of cold blue touch up. Use with caution, adjust, measure and repeat.
Christmas surprise (26.12.2016)
Unsightly crimp in my over under vent rib near the mid sight. Took it to three gunsmiths. Two refused to fix it and one wanted $150 and to remove my mid sight mark. I said no and lived with the crimp for a year. Then this Christmas my wife ordered the Murray vent rib tool from Brownells.. Was just going to test the fit of the tool and realized I could fix it. Took me seconds and my barrell was good as new. Every shotgunner with vent ribs needs this tool.