Distinctive Design Adds That Individual Touch; Driver Included
Offers positive driver purchase plus a touch distinction to set your 1911 Autos apart from the others. Three, deep recesses arranged in a great-looking symmetrical design.
SPECS: Stainless steel, heat treated, .150"-50 x .250". Sold 4 screws per pak. Includes Tri-wing driver.
Lisää...
Erikoismuotoilu Lisää Yksilöllisyyttä; Meisseli Sisältyy
Tarjoaa varman meisselin otteen sekä lisää ainutlaatuista erottuvuutta asettaaksesi 1911 Autosi erilleen muista. Kolme, syvää koloa järjestetty hienosti symmetriseen muotoiluun.
TEKNISET TIEDOT: Ruostumatonta terästä, lämpökäsitelty, .150"-50 x .250". Myydään 4 ruuvin pakkauksissa. Sisältää Tri-wing -ruuvimeisselin.
Arvioiden lukumäärä: 6
Arvostelut brownells.com sivustolla: 6
Arvioiden keskiarvo: 2,7
Don't Bother(24.6.2010)
This product, while looking good, is horrible. The driver bit, no matter how much attention is payed and cautiousness used will strip the head.
VERY TALL Heads; perfect for THICK Grip(21.7.2010)
'Should be known that these WILL Stick out CONSIDERABLY, and if you want to use them for standard thickness grips you will likely be disappointed. For THICK grips they'd be superb.! They look great in profile in any case.
Tri=wing grip screws 1911(23.12.2011)
Look great work like junk. first two of the screws have a different finish. noticed after installing, came close to striping one screw that had to be removed to match finish of other. Would not buy these again
to soft(28.7.2014)
The screw head stripsout very easily. They look good on 2 of my comp 1911's, but poor quality...
Secure(19.5.2015)
Used to replace factory screws on 7 - 1911's in the past 4 years. Remain tight. Have experienced no problems.
Alot better than the reviews (24.2.2018)
First things first, is it easy to strip a screw in general flat head or other wise? Answer: yes if you over tighten or if you have a poor fit from the driver and the fastener.
With that said I love this grip screw!!!
With the rubber o-ring installed and tightened down these things are amazing they look great and if you decide to use magpul FDE grips I cannot imagine one looking better.
I was a little worried after reading the reviews. However, I feel that they are not taking into account of what caused them to strip(that being more of a user error than a performance issue). They threaded on perfect, snugged up and tighten down perfectly. Being completely honest on one of the screws as I was torquing it down I started to feel the driver bit lose contact with the screw head. I stopped immediately repositioned my screwdriver and finished up.
I ordered these for my S&W but I but one in my build project with magpul FDEs and they look so good I want to order another set for it.
My advice just slow down and take your time. I am sad to see these screws go.
Distinctive Design Adds That Individual Touch; Driver Included
Offers positive driver purchase plus a touch distinction to set your 1911 Autos apart from the others. Three, deep recesses arranged in a great-looking symmetrical design.
SPECS: Stainless steel, heat treated, .150"-50 x .250". Sold 4 screws per pak. Includes Tri-wing driver.
Lisää...
Erikoismuotoilu Lisää Yksilöllisyyttä; Meisseli Sisältyy
Tarjoaa varman meisselin otteen sekä lisää ainutlaatuista erottuvuutta asettaaksesi 1911 Autosi erilleen muista. Kolme, syvää koloa järjestetty hienosti symmetriseen muotoiluun.
TEKNISET TIEDOT: Ruostumatonta terästä, lämpökäsitelty, .150"-50 x .250". Myydään 4 ruuvin pakkauksissa. Sisältää Tri-wing -ruuvimeisselin.
Arvioiden lukumäärä: 6
Arvostelut brownells.com sivustolla: 6
Arvioiden keskiarvo: 2,7
Don't Bother(24.6.2010)
This product, while looking good, is horrible. The driver bit, no matter how much attention is payed and cautiousness used will strip the head.
VERY TALL Heads; perfect for THICK Grip(21.7.2010)
'Should be known that these WILL Stick out CONSIDERABLY, and if you want to use them for standard thickness grips you will likely be disappointed. For THICK grips they'd be superb.! They look great in profile in any case.
Tri=wing grip screws 1911(23.12.2011)
Look great work like junk. first two of the screws have a different finish. noticed after installing, came close to striping one screw that had to be removed to match finish of other. Would not buy these again
to soft(28.7.2014)
The screw head stripsout very easily. They look good on 2 of my comp 1911's, but poor quality...
Secure(19.5.2015)
Used to replace factory screws on 7 - 1911's in the past 4 years. Remain tight. Have experienced no problems.
Alot better than the reviews (24.2.2018)
First things first, is it easy to strip a screw in general flat head or other wise? Answer: yes if you over tighten or if you have a poor fit from the driver and the fastener.
With that said I love this grip screw!!!
With the rubber o-ring installed and tightened down these things are amazing they look great and if you decide to use magpul FDE grips I cannot imagine one looking better.
I was a little worried after reading the reviews. However, I feel that they are not taking into account of what caused them to strip(that being more of a user error than a performance issue). They threaded on perfect, snugged up and tighten down perfectly. Being completely honest on one of the screws as I was torquing it down I started to feel the driver bit lose contact with the screw head. I stopped immediately repositioned my screwdriver and finished up.
I ordered these for my S&W but I but one in my build project with magpul FDEs and they look so good I want to order another set for it.
My advice just slow down and take your time. I am sad to see these screws go.