Yli 300 000 asiakasta - kiitämme teitä!

Yli 40 000 tuotetta metsästykseen ja ammuntaan

Vaihda 10/22® SOCKET HEAD TAKEDOWN SCREW rumaan alkuperäiseen. 💡 Nopeampi tukin irrotus ja ainutlaatuinen ilme! Sopii Ruger 10/22.
  • VOLQUARTSEN SOCKET HEAD TAKEDOWN SCREW
  • VOLQUARTSEN SOCKET HEAD TAKEDOWN SCREW
  • VOLQUARTSEN SOCKET HEAD TAKEDOWN SCREW
  • VOLQUARTSEN SOCKET HEAD TAKEDOWN SCREW
  • VOLQUARTSEN SOCKET HEAD TAKEDOWN SCREW

VOLQUARTSEN 10/22® SOCKET HEAD TAKEDOWN SCREW - VOLQUARTSEN SOCKET HEAD TAKEDOWN SCREW

810162010577 930000026

Ominaisuudet

  • Asetyyppi: Ruger
  • Malli: 10/22
  • Toimituksen paino: 0,005kg
  • Toimituksen korkeus: 15mm
  • Toimituksen leveys: 71mm
  • Toimituksen pituus: 86mm
  • UPC: 810162010577

Tuotekuvaus

Made in USA
  • Tekniset tiedot:
  • Malli: 10/22
  • Merkki: Ruger
17.9 17.9 1 EUR
17.9 EUR 17,90 €

Hintoihin sisältyy ALV, toimitus aina 10€ per tilaus.

Tuotenro: 930000026

Valm.nro: VC10TD

810162010577 Korvike tehdasruuville, joka poistaa rumat, kuluneet ja vaurioituneet ruuvipaikat. Mahdollistaa nopeamman ja helpomman tukin poistamisen sekä lisää ainutlaatuisen räätälöidyn ilmeen 10/22®:si. Ei muutoksia tukkiin tai vastaanottimeen.
Varastossa

Toimitusaika noin 2-4 viikkoa.
Yli 10 kpl. USA:n varastossa

1
2
3
4
5
6
7
8
9
10+

Toimitusaika noin 2-4 viikkoa.
Yli 10 kpl. USA:n varastossa

  • Tekniset tiedot:
  • Malli: 10/22
  • Merkki: Ruger

Kuvaus:

Näytä alkuperäinen (englanti)
Houkutteleva & Turvallinen
Korvike tehdasruuville, joka poistaa rumat, kuluneet ja vaurioituneet ruuvipaikat. Mahdollistaa nopeamman ja helpomman tukin poistamisen sekä lisää ainutlaatuisen räätälöidyn ilmeen 10/22®:si. Ei muutoksia tukkiin tai vastaanottimeen.

TEKNISET TIEDOT: Karkaistu teräs, musta, mattapinta. Sopii 10/22 ja 10/22 Magnum.

Ominaisuudet

  • Asetyyppi: Ruger
  • Malli: 10/22
  • Toimituksen paino: 0,005kg
  • Toimituksen korkeus: 15mm
  • Toimituksen leveys: 71mm
  • Toimituksen pituus: 86mm
  • UPC: 810162010577

Tuotekuvaus

Made in USA

Asiakasarvostelut

Asiakasarviot (11)

3,8 / 5
En suosittele

Brownells USA Not Quite the Real Thing 14.8.2014

This screw is 1/8" shorter than the screw furnished by Ruger. And now (2014) that Ruger has standardized on a socket head screw you're better off with the real thing. After trying this one, I bought two from Ruger. They cost half as much as the VQ.

Suosittelen ehdottomasti

Brownells USA Fit Fine For This Build 27.7.2013

Built a 10/22 using:

Timney 10/22 Drop-In Trigger Assembly 883-000-038WB -- great trigger, drop in with no fitting required. The lever magazine release is a great addition, helping with making the rifle a little more ambidextrous. The spring loaded bolt release works as we are accustomed to unlike the factory release. The trigger pull is crisp and clean reminiscent of the Jewel triggers on my 700. The trigger is a vast improvement over factory. 4 stars as the pull measured 3lbs on my Lyman gauge, preferred for hunting but as it is not adjustable I don't consider this a bench rest trigger.

ER Shaw Fluted 10/22 .920 Target Barrel, SS 100-004-747WB -- everything I was looking for. Looks great and shoots great. 1/2" groups at 75 yards on a 100 degree, 10 - 15 mph gusty day with 20 year old Remington Golden Bullet HP, very satisfying. The barrel dropped right into the action and was installed using the factory V-block without barrel droop. V-block barrel retaining screws were just snugged. Checked with a set of headspace gauges and everything was fine and good to go. A 5 star barrel for sure.

Hogue 10/22 Overmolded Rifle Stock B/B Rubber Covering 408-220-100WB -- The stock I wanted was out of stock so I got this one to do the build. I am liking it. Feels good in hand and on the shoulder. Ambidextrous Bedding was accurate and felt solid. With the action screw torqued to 18 in-lbs the Shaw barrel was dollar bill free floated from 1" behind the flutes to the muzzle. The semi-varmint fore end is a joy in hand or on a bag. 4 Stars as the fore end will flex enough to touch the barrel with moderate straight line side hand pressure, a hasty sling or tight sling. Still I may well forget about the stock I wanted that cost 2-1/2 times as much, this one shoots and feels so good.

Volquartsen 10/22 Socket Head Takedown Screw 930-000-O26WB -- Comparing this screw to my factory screw it is about 2-1/2 threads shorter. However it fit this build just fine, earning it 5 Stars. It and the receiver handled 18 in-lbs of torque without problem.

Tiesitkö?

Valmistajan tiedot

Vastuullinen taloudellinen toimija EU-asetuksen mukaisesti

Brownells Finland Oy
Kutojantie 3
02630 Espoo
Suomi
tiedustelut@brownells.fi

Ups! Jotain meni pieleen.

Kohdattiin virhe tämän sisällön lataamisessa. Päivitä sivu jatkaaksesi. Jos ongelma jatkuu, ota yhteyttä asiakaspalveluumme.

Takaisin alkuun