Korisi on tyhjä.

Ostoskori

Apu ja yhteydenotto

Ilmainen toimitus yli 250€ perustoimituksille

100:n päivän palautusoikeus

Uutiskirje

Tarjoukset

Yli 300 000 asiakasta - kiitämme teitä!

4,93/5 "Erittäin hyvä" (1400+ arvostelua)

Yli 40 000 tuotetta metsästykseen ja ammuntaan

SEEKINS PRECISION
SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

811452029309 100018841

90 degree standard throw lever 60 degree short throw lever Available in black Drop in replacement for Mil-Spec selector switch Fully ambidextrous Not recommended to be used with the Hipertouch trigger

Lisää...

90 asteen vakioheitinvipu 60 asteen lyhyt heitinvipu Saatavilla mustana Vaihtokappale Mil-Spec-valitsinkytkimelle Täysin kaksikätinen Ei suositella käytettäväksi Hipertouch-liipaisimen kanssa

Lisää...

Asiakasarviot: SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

Arvioiden lukumäärä: 6
Arvostelut brownells.com sivustolla: 6
Arvioiden keskiarvo: 3,5

Loose fit (11.3.2016)

There is a 3/32" gap between the receiver and the safety lever on each side of the receiver. Almost slips over the stops on the receiver. Also, the anodizing on one of the levers is purple instead of black. I will be returning this. This is the first Seekins product I have ever had an issue with.

Great product (29.3.2016)

Super easy to install, especially liked the way you can switch the controls to be 60 or 90 degrees just by turning over the base. Way better pricing than other versions on the market.

Well made, easy install, good fit. (23.3.2017)

Purchased two of these in black. Installed one in a Palmetto AR9 and the other in a Palmetto AR15. Both went in without difficulty, look good, and operate well. I shoot left-handed and this product makes manipulating the safety much easier.

Didn't fit on two different rifles. (27.4.2017)

This is my 3rd Seekins ambi safety and I've been pleased up to this point. The first two I purchased were installed on Palmetto State Armory lowers and they went in and function without issue. Based on those experiences I purchased a 3rd Seekins for use on a factory Daniel Defense rifle. The safety seems a bit overlarge in diameter as it was very tight when inserted in the first hole in the receiver, and could not be pushed all the way to the other side. I then tried to install the safety on a factory Armalite rifle, and again would not fit. Fortunately I had another rifle with a Palmetto receiver that had a CAA ambi safety installed. I removed the CAA and installed the Seekins in the Palmetto without difficulty. The CAA safety was then installed in the Armalite rifle without difficulty. I could have done a bit of careful fitting and probably gotten the Seekins to fit in the Armalite and Daniel Defense but I don't really want to be sanding on an anodized part.

Maybe not. (4.6.2017)

Safety was mot mil spec diameter. Would not fit at all in hole, when standard mil spec single selector safety dropped right in. Had to auger it into both holes so it milled out some of the aluminum lower receiver. Finally took an emery cloth to it and filed it down on both ends of the shaft. Put the lower together and it wouldn't go full 12 o'clock to release the trigger without using your thumb to give it that extra millimeter(s). Bad tetent channel maybe? Took it out and reversed it so it's now a short throw.... now it works, but a lot or work and not a cheap safety for the trouble it gave me.

Suprised! (13.12.2017)

I did not actually read the product description nor reviews when i ordered it. I thought it was just a regular ambi safety with fancy arms. When i got it, i realized that it has 2 safety groove cut in it, 1 side is the regular 90 degree cut and the other side is 60 degree short throw cut. That is a bonus for me as i have both regular marked lowers and 60 degree sts marked lowers.

I did not experienced any fitment issue that other reviewers have. It fitted my Noveske, aero precision, armalite and spike tactical lowers. It is a tighter fit in my Noveske, which i believe has everything to do with the fact that Noveske cerakote and anodize all their lowers.

I will be buying a few more of these.

Lue 6 arvostelua lisää brownells.com sivustolla

109.9 109.9 1 EUR

Tuotenro: 100018841
SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK
Valmistajan tuotenumero: 11580002 811452029309 90 asteen vakioheitinvipu 60 asteen lyhyt heitinvipu Saatavilla mustana Vaihtokappale Mil-Spec-valitsinkytkimelle Täysin kaksikätinen Ei suositella käytettäväksi Hipertouch-liipaisimen kanssa

109.9 EUR 7 109,90 € *

Toimitusaika noin 2-4 viikkoa.
7 kpl. USA:n varastossa

Ominaisuudet: Merkki: AR-15

Lisää toivelistaan

Kysy tuotteesta

Tiedot

Lisää toivelistaan

Kysy tuotteesta

Ominaisuudet

Valmistaja: AR-15 Toimituksen paino: 0,018kg Toimituksen korkeus: 6mm Toimituksen leveys: 83mm Toimituksen pituus: 108mm UPC : 811452029309

Tuotekuvaus

Made in USA
USA:n vientiluvan tyyppi: 0A501.x

Tutustu Seekins Precisionin ambidextrous Safety Selector Kit:iin mustana. 🔧 Täydellinen AR-15:lle, ei suositella Hipertouchilla.

Lisää...

90 asteen vakioheitinvipu 60 asteen lyhyt heitinvipu Saatavilla mustana Vaihtokappale Mil-Spec-valitsinkytkimelle Täysin kaksikätinen Ei suositella käytettäväksi Hipertouch-liipaisimen kanssa

Lisää...

Asiakasarviot: SEEKINS PRECISION SAFETY SELECTOR KIT, AMBIDEXTROUS, BLACK

Arvioiden lukumäärä: 6
Arvostelut brownells.com sivustolla: 6
Arvioiden keskiarvo: 3,5

Loose fit (11.3.2016)

Great product (29.3.2016)

Super easy to install, especially liked the way you can switch the controls to be 60 or 90 degrees just by turning over the base. Way better pricing than other versions on the market.

Well made, easy install, good fit. (23.3.2017)