Yli 300 000 asiakasta - kiitämme teitä!

Yli 40 000 tuotetta metsästykseen ja ammuntaan

Tee ruuvien hiominen helpoksi Brownells Screw Checker/Shortening Jigillä! 🔧 Karkaistusta teräksestä, valmistettu Yhdysvalloissa.
  • BROWNELLS SCREW CHECKER/SHORTENING JIG
  • BROWNELLS SCREW CHECKER/SHORTENING JIG

BROWNELLS SCREW CHECKER/SHORTENING JIG - BROWNELLS SCREW CHECKER/SHORTENING JIG

050806015920 080574001

Ominaisuudet

  • Toimituksen paino: 0,023kg
  • Toimituksen leveys: 83mm
  • Toimituksen pituus: 146mm
  • UPC: 050806015920
27.9 27.9 1 EUR
27.9 EUR 27,90 €

Hintoihin sisältyy ALV, toimitus aina 10€ per tilaus.

Tuotenro: 080574001

050806015920 Erityisiin töihin käytä tätä kovametallista Checker/Shortener Jig -työkalua, joka tekee ruuvien hionnasta oikeaan pituuteen nopeaa ja helppoa.
Varastossa
1
2
3
4
5
6
7
8
9
10+

Kuvaus:

Näytä alkuperäinen (englanti)
Erityisiin töihin käytä tätä kovametallista Checker/Shortener Jig -työkalua, joka tekee ruuvien hionnasta oikeaan pituuteen nopeaa ja helppoa.

ERITTÄIN: Yhdysvalloissa valmistettu, sinistetty.

Ominaisuudet

  • Toimituksen paino: 0,023kg
  • Toimituksen leveys: 83mm
  • Toimituksen pituus: 146mm
  • UPC: 050806015920

Asiakasarvostelut

Asiakasarviot (3)

3,7 / 5
Suosittelen jossain määrin

Brownells USA loose sloppy threads 24.11.2014

I bought this to cut down some 6-48 screws to fit in a Winchester 1300 shotgun receiver so they would stop just short of projecting into the receiver. I used brand new Brownells 6-48 Torx head screws.



The screws are a VERY loose fit in the threads - poor thread engagement - so despite the tool being at least 1/8" thick and there being several threads there, the screws are not held securely in the tool. The only way I could figure out to hold the screw steady while cutting it down was to "pinch" it from the head end of the screw and pull it back against the poorly-tapped threads to force a modicum of "thread engagement", keep the screw relatively square/plumb for the cut operation, and to keep some tension on the screw so it wouldn't wobble and spin around while I was cutting it with a dremel. Which means my thumb and forefinger got hot several times.



VERY dissatisfied with this product. I have already marked up the tool cutting the first screw with it, but I will be contacting Brownells about a refund. Of course, it will cost me about the same I paid for it to ship it back. Funny how that works... I "get" that Brownells has to make a profit to stay in business, but I expected the threads to be tapped a lot better for a tool specifially made to cut screws with. I also have no realistic expectation that these poorly tapped threads are going to do any significant amount of "chasing" the threads of the cut screw once I remove it from the tool.



Next time I will just make my own. I did a LOT better job of tapping the threads on my shotgun receiver and that was the first time I have EVER drilled and tapped threads on a gun part. There is almost zero screw wobble on my tapped threads.



Shame on you, Brownells.

Suosittelen ehdottomasti

Brownells USA What a GREAT idea !!! 6.6.2013

It is one of those things that I did not know existed. I now wonder how I ever got along without it. I salute you !!!

Tiesitkö?

Valmistajan tiedot

Vastuullinen taloudellinen toimija EU-asetuksen mukaisesti

Brownells Finland Oy
Kutojantie 3
02630 Espoo
Suomi
tiedustelut@brownells.fi

Ups! Jotain meni pieleen.

Kohdattiin virhe tämän sisällön lataamisessa. Päivitä sivu jatkaaksesi. Jos ongelma jatkuu, ota yhteyttä asiakaspalveluumme.

Takaisin alkuun