Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Trimmaa kärkinaulan kärjen, jotta rikkoutuneen heittimen jousen poisto on yksinkertaista
Onttopäinen jyrsin sopii porakoneeseen, tasoittaa kärkinaulan etupään poistaen vain taotun alueen. Mahdollistaa usein olemassa olevan kärkinaulan uudelleentaonnin ja välttää vastaanottimen uudelleen sinistämisen.
TEKNISET TIEDOT: Teräksinen varsi, karkaistu terästerä. Pituus 2½" (6,3 cm), varren halkaisija .31" (7,8 mm). Leikkurin halkaisija .143" (3,6 mm).
Lisää...
Asiakasarviot: BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 5
Great investment!(10.2.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).
Tuotenro: 080000040 BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER050806103825 Onttopäinen jyrsin sopii porakoneeseen, tasoittaa kärkinaulan etupään poistaen vain taotun alueen. Mahdollistaa usein olemassa olevan kärkinaulan uudelleentaonnin ja välttää vastaanottimen uudelleen sinistämisen.
59.9EUR059,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Trims The Rivet Tip To Make Broken Ejector Spring Removal Simple
Hollow-end mill fits in drill press, spot faces the front rivet to take off just the peened area. Often lets you re-peen the existing rivet and eliminate rebluing the receiver.
Trimmaa kärkinaulan kärjen, jotta rikkoutuneen heittimen jousen poisto on yksinkertaista
Onttopäinen jyrsin sopii porakoneeseen, tasoittaa kärkinaulan etupään poistaen vain taotun alueen. Mahdollistaa usein olemassa olevan kärkinaulan uudelleentaonnin ja välttää vastaanottimen uudelleen sinistämisen.
TEKNISET TIEDOT: Teräksinen varsi, karkaistu terästerä. Pituus 2½" (6,3 cm), varren halkaisija .31" (7,8 mm). Leikkurin halkaisija .143" (3,6 mm).
Lisää...
Asiakasarviot: BROWNELLS REMINGTON 870 EJECTOR SPRING RIVET CUTTER
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 5
Great investment!(10.2.2016)
This little rivet cutter made me save over $200 in gunsmithing work on my old 870 Wingmaster, which had been sitting in the gun safe for years because of a ''too-expensive-to-replace'' broken ejector spring. The instructions provided with the tool are very clear and allowed me, as indicated, to re-use the rivet to lock the new spring into the ejector. The only thing I did differently than prescribed by the instructions was to drive the rivet cutter down on the tiny rivet head by hand instead of using a press drill. The rivet cutter being very sharp and the rivet metal being very soft, I was afraid to ruin the rivet using a press drill. It took me 10 minutes to cut the rivet head slowly and safely by hand (clockwise twist of the fingers with little pressure).