Hammer has three heads; brass, nylon and steel. Two heads mount to the blued steel hammer head, to the blued steel hammer head, the third attached to the base of the knurled brass handle. Brass drift punch stores in handle. Great for knocking out pins.
Lisää...
Vasarassa on kolme päätä; messinki, nailon ja teräs. Kaksi päätä kiinnittyy sinistetyn teräksen vasaranpäähän, kolmas on kiinnitetty uurteisen messinkisen kahvan pohjaan. Messinkinen lävistysnaskali säilytetään kahvassa. Erinomainen tapitusnastojen irrottamiseen.
Lisää...
Asiakasarviot: LYMAN BRASS TAPPER AND DRIFT PUNCH
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 4
It has limits. (6.10.2017)
It's a neat little hammer and punch kit. You can keep the brass head and steel head in the hammer for a bit more power, or remove them both and use the plastic head only for delicate tasks. For lite use, such as driving pins, this kit is perfect. The punch fits inside the hollow handle. Think: "lite use" with this kit.
I used it to remove and install dovetail sights (both front and rear) on several older and newer .22LR rifles. A couple of my front sights were really tough to remove, but I stayed at it. The job really deformed the head of the brass punch. It almost looks like a mushroomed bullet that I recovered from an Elk. I originally bought it to keep in my travel gear, with the intent of using it to drift sights at the range. It might work for that purpose, provided the sights are not really tight. But, as I stated above, it's really not up to that task. I've ordered a stronger (?) drift punch, and hope it holds up to sight installation. I'm going to try to file this deformed punch flat. Good luck.
Tuotenro: 749002611 LYMAN BRASS TAPPER AND DRIFT PUNCH Valmistajan tuotenumero: 7031290011516812902 Vasarassa on kolme päätä; messinki, nailon ja teräs. Kaksi päätä kiinnittyy sinistetyn teräksen vasaranpäähän, kolmas on kiinnitetty uurteisen messinkisen kahvan pohjaan. Messinkinen lävistysnaskali säilytetään kahvassa. Erinomainen tapitusnastojen irrottamiseen.
54.9EUR054,90 €
*
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.
Hammer has three heads; brass, nylon and steel. Two heads mount to the blued steel hammer head, to the blued steel hammer head, the third attached to the base of the knurled brass handle. Brass drift punch stores in handle. Great for knocking out pins.
Lisää...
Vasarassa on kolme päätä; messinki, nailon ja teräs. Kaksi päätä kiinnittyy sinistetyn teräksen vasaranpäähän, kolmas on kiinnitetty uurteisen messinkisen kahvan pohjaan. Messinkinen lävistysnaskali säilytetään kahvassa. Erinomainen tapitusnastojen irrottamiseen.
Lisää...
Asiakasarviot: LYMAN BRASS TAPPER AND DRIFT PUNCH
Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 4
It has limits. (6.10.2017)
It's a neat little hammer and punch kit. You can keep the brass head and steel head in the hammer for a bit more power, or remove them both and use the plastic head only for delicate tasks. For lite use, such as driving pins, this kit is perfect. The punch fits inside the hollow handle. Think: "lite use" with this kit.
I used it to remove and install dovetail sights (both front and rear) on several older and newer .22LR rifles. A couple of my front sights were really tough to remove, but I stayed at it. The job really deformed the head of the brass punch. It almost looks like a mushroomed bullet that I recovered from an Elk. I originally bought it to keep in my travel gear, with the intent of using it to drift sights at the range. It might work for that purpose, provided the sights are not really tight. But, as I stated above, it's really not up to that task. I've ordered a stronger (?) drift punch, and hope it holds up to sight installation. I'm going to try to file this deformed punch flat. Good luck.