Just because you carry a compact pistol doesn't mean you have to accept a stiff, rough trigger pull. These replacements for your Glock 42/43/43x/48 factory trigger connector improve the entire trigger pull by shortening the overall pull, eliminating over-travel, and providing a faster reset. Reduces trigger pull weight by an average of 2.5 lbs. Also removes the notorious "Glock bump" caused by the trigger bar hitting the connector, which makes the shooter apply extra force to get over the bump, typically moving the pistol off target. Edge is a drop-in replacement for factory part.
Lisää...
Tasoittaa, keventää ja parantaa liipaisimen tuntumaa
Kompaktin pistoolin kantaminen ei tarkoita, että sinun täytyy tyytyä jäykkään ja karheaan liipaisimen vetoon. Nämä korvaavat osat Glock 42/43/43x/48 tehdasliipaisimen liittimelle parantavat koko liipaisimen vetoa lyhentämällä vetomatkaa, poistamalla ylivetoa ja tarjoamalla nopeamman palautuksen. Vähentää liipaisimen vetopainoa keskimäärin 2,5 lbs. Poistaa myös kuuluisan "Glock-nypyn", joka johtuu liipaisintangon osumisesta liittimeen, mikä vaatii ampujalta ylimääräisen voiman käyttämistä nypyn ylittämiseen, mikä tyypillisesti siirtää pistoolia kohteesta ohi. Edge on suoraan vaihdettavissa tehdasosan tilalle.
Arvioiden lukumäärä: 15
Arvostelut brownells.com sivustolla: 15
Arvioiden keskiarvo: 4,1
Glock 42/43 Ghost connector (30.5.2015)
Worked great in both my Glock 42 & 43. Reduced the pull weight and smoothed out the pull.
Best improvement to G43?(10.7.2015)
Like many people, I have been disappointed with GLOCK's gen4 trigger pull, being used to gen2's and gen3's. When I got my G43 I immediately noticed the trigger was quite a bit heavier than what I was used to. Since no gen3 trigger with trigger bar exists for the G43, this caught my eye. Man, what a difference! Brings the trigger pull back down to gen2/3 levels that I'm used to. Very easy to install and makes a huge improvement.
Great Product(3.9.2015)
Installed this in my Glock 43 and couldn't believe how well it worked. My trigger pull measured 6 Ibs before installation and 4.5 Ibs after. It was such an improvement that I actually had to adjust my sights because I was no longer pulling to one side. I recommend this to any Glock 43 owner, extremely easy to install as well!
Not great(29.9.2015)
I installed this on a Glock 42. Preferred the factory pull and reset. I've used the Glock aftermarket connectors for lighter pull and been very pleased. This did not seem to fit the 42 well. It worked, but no discernable improvement and softer break.
Created sloppy trigger pull(23.10.2015)
Bought this for my G43 and installed it. It made the trigger pull a tad bit lighter, however; the difference is negligible. Most noticeably it made the trigger pull sloppy and created more creep. The factory trigger connector makes for a cleaner break. Sending this one back!
Great product(13.12.2015)
Installed this in my G43 and am very pleased with the result. The stock G43 trigger had a crisp but very heavy break. With the Ghost connector only a small amount of crispness in the break is sacrificed at the gain of being over 2 lbs lighter. I'm able to place shots more accurately now which is VERY important IMO. Trigger now measures 5 lbs and feels similar to my other Glocks that have 3.5lbs connector.
Must buy(10.2.2016)
I hope prior reviewers read this so they get the Gen 3 Trigger bar information. The Suarez Trigger I mention is what you are looking for.
This is my second EDGE connector. I have one that has seen use in a G27 and G22/17. Awesome connector. Highly recommended. You should also head on over to www.suarezinternational.com and buy his Glock Triggers to go with this connector. His triggers are simply the absolute BEST triggers for Glock, I have 3 of them. The Ghost Edge connector on the Glock 43, coupled with the Suarez trigger is THE combination for the 43 (or any Glock really) and will give you a trigger your friends won't believe.
Ghost does it again(10.4.2016)
Very easy to install, no need to remove the trigger and trigger pin. Dropped right in. Measured trigger pull prior to install. 9lbs 14oz. After install and a little polishing. trigger pulled at 5lbs.14oz which is almost a glock 17 factory pull. Great item. mush have.
Best under $20 Upgrade (9.5.2016)
Just installed this bad boy in a Glock 42 and couldn't be happier. I was at 10.5 lbs average trigger pull before the install and now it's at 6.15 lbs. Not much more you can say about it. Seriously best under $20 upgrade I have ever done on any gun.
Review Of the Ghost Connector, G43(30.6.2016)
I recently purchased a new Glock 43 but found the trigger was so heavy that it actually abaded my trigger finger. The safety lever in the trigger was sharp and rough. My NRA trigger pull weights are packed away but I estimate that the pull weight was around 8 to 9 lbs or even more. I like the Glock "take-up first stage but the 2nd stage was horrible. I tried the .50 polishing job and that did not work in the least. The gunsmith from where I bought it claimed it had a 6.5 lbs pull but he would not allow me to see him do this operation. I tested another G43 in the store and it's TP was excellent. I installed the Ghost Connector and there was an immediate mild to moderate smooth improvement in the 2nd stage. I estimate that 2 lbs were taken off. They should call it the "5.5 lbs connector". I am very pleased with it but wish it were even lighter. With dry fire and actual practice it should get even smoother.I am a Glock and other brand certified Armorer.
Great improvement on Glock 43(29.10.2016)
Easy to install, dropped right in. The trigger is much lighter and crisper than the stock OEM trigger. It is not too light to be unsafe for a carry gun. I am so pleased with the results, I am now a Ghost fan! Highly recommended!
installed drop-in trigger connector(24.11.2016)
The Edge drop-in trigger for my Glock 42 fit well, was easy to install and looked like a good quality product. It reduced the factory trigger pull from 7.8 pounds to 5.3 pounds. Still a little heavy but much better to shoot.
You've been warned(27.12.2016)
Installed on stock glock 43 trigger group. Made the break more rounded and less crisp (ak like) but lighter. Didn't like the feel of the sponge like roundedness and loss of a clearly identified wall. Use gun for personal defense and placed top 3 in multiple bug competitions. I do recommend tango down slide release and their +2 mag extensions for this platform
Minor Improvement, but worth it(29.3.2017)
Installed the Ghost Edge connector in my wife's Glock 43 and it reduced the trigger pull from 5.5 lb to 4 lb 13 oz. A little improvement, but not as much as I expected. The pistol has less than 100 rounds through it, so it may lighten up some more as she uses it. Haven't taken it to the range yet to see how/if it improves her shooting.
Major Improvement (14.3.2018)
A major improvement if you have an early G42/43 with the factory 33215 connector. I loved the size and packability of the G43 but hated that trigger pull. Upgraded to the Ghost Edge and world of difference. I picked up another G43 that had updated factory 33564 connector and found the Ghost was smoother but improvement was subtle.
Tuotenro: 100017381 GHOST G42/43/43X/48 DROP-IN TRIGGER CONNECTOR Valmistajan tuotenumero: GHO_42-43-2424-813978020006 Kompaktin pistoolin kantaminen ei tarkoita, että sinun täytyy tyytyä jäykkään ja karheaan liipaisimen vetoon. Nämä korvaavat osat Glock 42/43/43x/48 tehdasliipaisimen liittimelle parantavat koko liipaisimen vetoa lyhentämällä vetomatkaa, poistamalla ylivetoa ja tarjoamalla nopeamman palautuksen. Vähentää liipaisimen vetopainoa keskimäärin 2,5 lbs. Poistaa myös kuuluisan "Glock-nypyn", joka johtuu liipaisintangon osumisesta liittimeen, mikä vaatii ampujalta ylimääräisen voiman käyttämistä nypyn ylittämiseen, mikä tyypillisesti siirtää pistoolia kohteesta ohi. Edge on suoraan vaihdettavissa tehdasosan tilalle.
45.9EUR5745,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Made in USA
USA:n vientiluvan tyyppi: 0A501.x
USA:n hallitus kontrolloi näitä tuotteita. Niiden vienti USA:sta on sallittu vain siihen maahan, johon ne on tilattu, ja vain vastaanottajan tai loppukäyttäjän käyttöön. Niitä ei saa uudelleenmyydä, siirtää tai luovuttaa mihinkään muuhun maahan tai muulle henkilölle kuin vastaanottajalle tai loppukäyttäjälle, ei alkuperäisessä muodossaan eikä muiden tuotteiden osana, ilman etukäteen hankittua lupaa USA:n hallitukselta tai muuta USA:n lakiin ja määräyksiin perustuvaa hyväksyntää.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Vastuullinen taloudellinen toimija EU-asetuksen mukaisesti
Brownells Finland Oy
Kutojantie 3
02630 Espoo
Suomi
tiedustelut@brownells.fi
Paranna Glock 42/43/43X/48 liipaisinta! 🔥 Tämä drop-in trigger connector lyhentää vetomatkaa ja vähentää vetopainoa. Kokeile nyt!
Just because you carry a compact pistol doesn't mean you have to accept a stiff, rough trigger pull. These replacements for your Glock 42/43/43x/48 factory trigger connector improve the entire trigger pull by shortening the overall pull, eliminating over-travel, and providing a faster reset. Reduces trigger pull weight by an average of 2.5 lbs. Also removes the notorious "Glock bump" caused by the trigger bar hitting the connector, which makes the shooter apply extra force to get over the bump, typically moving the pistol off target. Edge is a drop-in replacement for factory part.
Lisää...
Tasoittaa, keventää ja parantaa liipaisimen tuntumaa
Kompaktin pistoolin kantaminen ei tarkoita, että sinun täytyy tyytyä jäykkään ja karheaan liipaisimen vetoon. Nämä korvaavat osat Glock 42/43/43x/48 tehdasliipaisimen liittimelle parantavat koko liipaisimen vetoa lyhentämällä vetomatkaa, poistamalla ylivetoa ja tarjoamalla nopeamman palautuksen. Vähentää liipaisimen vetopainoa keskimäärin 2,5 lbs. Poistaa myös kuuluisan "Glock-nypyn", joka johtuu liipaisintangon osumisesta liittimeen, mikä vaatii ampujalta ylimääräisen voiman käyttämistä nypyn ylittämiseen, mikä tyypillisesti siirtää pistoolia kohteesta ohi. Edge on suoraan vaihdettavissa tehdasosan tilalle.
Arvioiden lukumäärä: 15
Arvostelut brownells.com sivustolla: 15
Arvioiden keskiarvo: 4,1
Glock 42/43 Ghost connector (30.5.2015)
Worked great in both my Glock 42 & 43. Reduced the pull weight and smoothed out the pull.
Best improvement to G43?(10.7.2015)
Like many people, I have been disappointed with GLOCK's gen4 trigger pull, being used to gen2's and gen3's. When I got my G43 I immediately noticed the trigger was quite a bit heavier than what I was used to. Since no gen3 trigger with trigger bar exists for the G43, this caught my eye. Man, what a difference! Brings the trigger pull back down to gen2/3 levels that I'm used to. Very easy to install and makes a huge improvement.
Great Product(3.9.2015)
Installed this in my Glock 43 and couldn't believe how well it worked. My trigger pull measured 6 Ibs before installation and 4.5 Ibs after. It was such an improvement that I actually had to adjust my sights because I was no longer pulling to one side. I recommend this to any Glock 43 owner, extremely easy to install as well!
Not great(29.9.2015)
I installed this on a Glock 42. Preferred the factory pull and reset. I've used the Glock aftermarket connectors for lighter pull and been very pleased. This did not seem to fit the 42 well. It worked, but no discernable improvement and softer break.
Created sloppy trigger pull(23.10.2015)
Bought this for my G43 and installed it. It made the trigger pull a tad bit lighter, however; the difference is negligible. Most noticeably it made the trigger pull sloppy and created more creep. The factory trigger connector makes for a cleaner break. Sending this one back!
Great product(13.12.2015)
Installed this in my G43 and am very pleased with the result. The stock G43 trigger had a crisp but very heavy break. With the Ghost connector only a small amount of crispness in the break is sacrificed at the gain of being over 2 lbs lighter. I'm able to place shots more accurately now which is VERY important IMO. Trigger now measures 5 lbs and feels similar to my other Glocks that have 3.5lbs connector.
Must buy(10.2.2016)
I hope prior reviewers read this so they get the Gen 3 Trigger bar information. The Suarez Trigger I mention is what you are looking for.
This is my second EDGE connector. I have one that has seen use in a G27 and G22/17. Awesome connector. Highly recommended. You should also head on over to www.suarezinternational.com and buy his Glock Triggers to go with this connector. His triggers are simply the absolute BEST triggers for Glock, I have 3 of them. The Ghost Edge connector on the Glock 43, coupled with the Suarez trigger is THE combination for the 43 (or any Glock really) and will give you a trigger your friends won't believe.
Ghost does it again(10.4.2016)
Very easy to install, no need to remove the trigger and trigger pin. Dropped right in. Measured trigger pull prior to install. 9lbs 14oz. After install and a little polishing. trigger pulled at 5lbs.14oz which is almost a glock 17 factory pull. Great item. mush have.
Best under $20 Upgrade (9.5.2016)
Just installed this bad boy in a Glock 42 and couldn't be happier. I was at 10.5 lbs average trigger pull before the install and now it's at 6.15 lbs. Not much more you can say about it. Seriously best under $20 upgrade I have ever done on any gun.
Review Of the Ghost Connector, G43(30.6.2016)
I recently purchased a new Glock 43 but found the trigger was so heavy that it actually abaded my trigger finger. The safety lever in the trigger was sharp and rough. My NRA trigger pull weights are packed away but I estimate that the pull weight was around 8 to 9 lbs or even more. I like the Glock "take-up first stage but the 2nd stage was horrible. I tried the .50 polishing job and that did not work in the least. The gunsmith from where I bought it claimed it had a 6.5 lbs pull but he would not allow me to see him do this operation. I tested another G43 in the store and it's TP was excellent. I installed the Ghost Connector and there was an immediate mild to moderate smooth improvement in the 2nd stage. I estimate that 2 lbs were taken off. They should call it the "5.5 lbs connector". I am very pleased with it but wish it were even lighter. With dry fire and actual practice it should get even smoother.I am a Glock and other brand certified Armorer.
Great improvement on Glock 43(29.10.2016)
Easy to install, dropped right in. The trigger is much lighter and crisper than the stock OEM trigger. It is not too light to be unsafe for a carry gun. I am so pleased with the results, I am now a Ghost fan! Highly recommended!
installed drop-in trigger connector(24.11.2016)
The Edge drop-in trigger for my Glock 42 fit well, was easy to install and looked like a good quality product. It reduced the factory trigger pull from 7.8 pounds to 5.3 pounds. Still a little heavy but much better to shoot.
You've been warned(27.12.2016)
Installed on stock glock 43 trigger group. Made the break more rounded and less crisp (ak like) but lighter. Didn't like the feel of the sponge like roundedness and loss of a clearly identified wall. Use gun for personal defense and placed top 3 in multiple bug competitions. I do recommend tango down slide release and their +2 mag extensions for this platform
Minor Improvement, but worth it(29.3.2017)
Installed the Ghost Edge connector in my wife's Glock 43 and it reduced the trigger pull from 5.5 lb to 4 lb 13 oz. A little improvement, but not as much as I expected. The pistol has less than 100 rounds through it, so it may lighten up some more as she uses it. Haven't taken it to the range yet to see how/if it improves her shooting.
Major Improvement (14.3.2018)
A major improvement if you have an early G42/43 with the factory 33215 connector. I loved the size and packability of the G43 but hated that trigger pull. Upgraded to the Ghost Edge and world of difference. I picked up another G43 that had updated factory 33564 connector and found the Ghost was smoother but improvement was subtle.
Apu ja yhteydenotto
(0) 
Uutiskirje
Perinteinen näkymä
Mobiilinäkymä