FORSTER PRODUCTS, INC.
FULL LENGTH SIZING DIES

757253001086 749004767

Forster Reloading Dies are of excellent quality and provide the reloader with the ability to produce concentric rounds time and time again. Each die is manufactured from the finest quality steel carefully machined to very tight tolerances. Dies are hand polished both before and after the heat-treating process to guarantee an extra fine finish. All Forster reloading dies feature their Forster Cross Bolt Die Locking Ring that tightens the two ends of the split ring instead of tightening a screw directly into the threads of the die. Forster Full Length Sizing Dies are each equipped with their E-Z Out Expander button which helps keep case necks concentric during the neck expanding operation. It's positioned higher in the neck area than most other dies. This provides support and holds the axis of the neck and case in alignment while the case is withdrawn from the die.

Lisää...

Forster Reloading Dies -täyden pituuden kokosarjaimet ovat erinomaista laatua ja mahdollistavat uudelleenlataajalle keskitettyjen patruunoiden valmistamisen toistuvasti. Jokaista sarjainta valmistetaan parhaasta laadun teräksestä, joka on koneistettu hyvin tarkkoihin toleransseihin. Sarjaimet kiillotetaan käsin sekä ennen että jälkeen karkaisuprosessin varmistaakseen ylimääräisen hienon viimeistelyn. Kaikissa Forsterin uudelleenlataussarjaimissa on heidän Forster Cross Bolt Die Locking Ring -lukitusrengas, joka kiristää jaetun renkaan kaksi päätä sen sijaan, että ruuvi kiristettäisiin suoraan sarjaimen kierteisiin. Forster Full Length Sizing Dies -sarjaimet on varustettu heidän E-Z Out Expander -napilla, joka auttaa pitämään hylsyn kaulan keskitettynä kaulan laajentamisen aikana. Se on sijoitettu korkeammalle kaula-alueelle kuin useimmissa muissa sarjaimissa. Tämä tukee ja pitää hylsyn kaulan ja hylsyn akselin linjassa, kun hylsy vedetään pois sarjaimesta.

Lisää...

Asiakasarviot: FORSTER PRODUCTS, INC. FULL LENGTH SIZING DIE, 8X57MM MAUSER

Arvioiden lukumäärä: 3
Arvostelut brownells.com sivustolla: 3
Arvioiden keskiarvo: 3,7

Cases won't chamber (11.9.2016)

I resized about 50 cases with the Forster National Match die and seated them with a Redding seating die. I didn't check them with my Wilson gauge and at the range discovered that almost all of them would not chamber in an AR-10 built with a Krieger barrel. When I checked them with a Wilson gauge they would not fit with the base sticking out of the bottom of the gauge. I tried resizing them again by overcamming in a Forster Coaxial Press and they were still too long. I tried the same case in a Redding bushing die and they were fine - even a little short as I adjusted to also overcam. With the Redding I have the option of bumping the shoulder less but the Forster makes them too long. I could have machined the bottom of the Forster die to bump the shoulder back but I should not have to do this. I have never had any problems with any Redding dies. I have no faith in the Forster dies although the Coaxial press is unequaled. I bought the 300 Win Mag National Match die also but I also returned it. With that much powder in the case I don't want to second guess. Will stick with Redding only.

Excellent dies (18.6.2017)

I use the .308 NM dies for an AR10t, and FN-FAL, and a DPMS Recon. I pretty much only use Lake City once fired brass that has been shot out of machine guns. I have had zero problems with these dies. I have had no issues. I bought a SAAMI min spec chamber gage and the NM die wouldn't size them enough to fit the gage although the loaded rounds still fit MY rifles. I believe this is because of a generous machine gun chamber. So I bought the Forster small base die (which I also give 5 stars to) so I could size this brass down a little more at the base and now all the cases fit the JPE SAAMI min Spec chamber gage as well. I believe I will be small base sizing these cases the first time I resize them from now on, not because I have had issues, but because it seems like a good idea to me. I seat all my .308 bullets with a Forster micrometer seater die which I also give five stars to. My run out, measured with a Hornady concentricity gage, is typically between less than .001" to .001" and my groups in all three of the aforementioned rifles are sub-MOA. The Forster dies are notorious for low run out. I have a Redding micrometer seater die for 300 win mag. It's good but all of my Forster micrometer seater dies are better. They are easier to adjust and read and you can use compressed loads with them unlike the Redding die which is a big problem IMHO. I have just ordered the Forster full length resizing die for 300 win mag to compliment my Forster Bushing neck sizing/shoulder bump die. I am perfectly happy to use nothing but Forster dies. They have never been anything but 5 stars for me.

Sizing issues. (15.7.2015)

Had a lee fl sizer but was removing brass from the neck area on sizing and the primer pin is tapered and larger than the hole in the lapua brass. Was afraid it would damage the necks in time. Got this die and works well. No brass erosion. primer remover pin straight and thinner. Have several other lee and forster dies. First time Ive had an issue with a lee.

Lue 3 arvostelua lisää brownells.com sivustolla

69.9 99.9 42 EUR

Tuotenro: 749004767
FORSTER PRODUCTS, INC. FULL LENGTH SIZING DIE, 8X57MM MAUSER
Valmistajan tuotenumero: 005651 757253001086 Forster Reloading Dies -täyden pituuden kokosarjaimet ovat erinomaista laatua ja mahdollistavat uudelleenlataajalle keskitettyjen patruunoiden valmistamisen toistuvasti. Jokaista sarjainta valmistetaan parhaasta laadun teräksestä, joka on koneistettu hyvin tarkkoihin toleransseihin. Sarjaimet kiillotetaan käsin sekä ennen että jälkeen karkaisuprosessin varmistaakseen ylimääräisen hienon viimeistelyn. Kaikissa Forsterin uudelleenlataussarjaimissa on heidän Forster Cross Bolt Die Locking Ring -lukitusrengas, joka kiristää jaetun renkaan kaksi päätä sen sijaan, että ruuvi kiristettäisiin suoraan sarjaimen kierteisiin. Forster Full Length Sizing Dies -sarjaimet on varustettu heidän E-Z Out Expander -napilla, joka auttaa pitämään hylsyn kaulan keskitettynä kaulan laajentamisen aikana. Se on sijoitettu korkeammalle kaula-alueelle kuin useimmissa muissa sarjaimissa. Tämä tukee ja pitää hylsyn kaulan ja hylsyn akselin linjassa, kun hylsy vedetään pois sarjaimesta.

94.9 EUR 0 94,90 € *

Ilmoita saatavuudesta

Ei saatavilla.

Ominaisuudet: Holkin tyyppi: Full Length Sizing Dies Patruuna: 8 mm Mauser (8 x 57 mm Mauser)

FORSTER PRODUCTS, INC. FULL LENGTH SIZING DIES

Asiakasarviot: FORSTER PRODUCTS, INC. FULL LENGTH SIZING DIE, 8X57MM MAUSER

Top takeaways

Ominaisuudet

Tuotekuvaus

Asiakasarviot: FORSTER PRODUCTS, INC. FULL LENGTH SIZING DIE, 8X57MM MAUSER

Yhdistä

Turvalliset maksutavat

Ammattijärjestöt

Tervetuloa!

FORSTER PRODUCTS, INC.
FULL LENGTH SIZING DIES