Forster makes a collet style bullet puller for standard seven eigths thru 14 threaded presses and a second collet style puller (both use the same Forster collets) for the Co-Ax Press. The FBP1010 puller for standard presses includes a collet tightening handle on top of the puller body. The FUP1010 Puller has a nine sixteenths inch hex top on the puller body which requires a wrench to tighten the collet. Both pullers easily remove bullets from almost any cartridge. Collets are sold separately.
Lisää...
Forster valmistaa hylsynkaulus-tyylisen luodinpoistajan, joka sopii standardiin seitsemän kahdeksasosaan 14 kierteisiin puristimiin, sekä toisen hylsynkaulus-tyylisen poistajan (molemmat käyttävät samoja Forsterin hylsyjä) Co-Ax puristimelle. FBP1010-poistaja standardipuristimille sisältää hylsyn kiristyskahvan poistajan rungon päällä. FUP1010-poistajassa on yhdeksän kuudettaosaa tuuman kuusikulmainen yläosa poistajan rungossa, joka vaatii avaimen hylsyn kiristykseen. Molemmat poistajat irrottavat helposti luodit lähes mistä tahansa patruunasta. Hylsyt myydään erikseen.
Lisää...
Asiakasarviot: FORSTER PRODUCTS, INC. UNIVERSAL BULLET PULLER, COLLETS NOT INCLUDED
Arvioiden lukumäärä: 3
Arvostelut brownells.com sivustolla: 3
Arvioiden keskiarvo: 2,7
Disapointing design(29.1.2012)
I purchased the puller from Sinclair along with three collets, thereby saving money rather than Forster dirctly. The puller I chose was the "Universal" with the hex head as in pic. The hex head is a soft metal nut, thread glued on a minor thread. On the second cartridge (6.5 x 55), the thread lock gave up and the hex head /nut, turned on its own. I am now left with no option but to use padded vice grips to extract the "collet screw body. Why not use a one piece "bolt". Remember the principle of KISS, less to go wrong. The quality of the collets however is high, but the "gripping force" exerted inside the puller by a tapering surface could be better finished, probably such tightening force was required. I would have gone for the Hornady Cam Lock, but, I don`t believe you can cover two calibers with one collet, 6.5/.264 & .257 Also, from Forsters I purchased a dozen pack of die lock rings. I was very disapointed to find them to be soft alloy. Now I happily find Sinclair do their own lock rings in stainless, well done.
Sent it back - would not buy again(15.6.2012)
Not up to the usual Forster quality. The collect nut is held on by lock-tite and came un-screwed on the tenth bullet I pulled. Do not waste your money.
Revised!(29.1.2015)
Product has been revised and now has an allen set screw that appears to be deep enough to seat into (or past) the threads of the collet pusher assembly. No way for the nut to turn now. Simple fix that should have been there from the beginning..., but live and learn. Buy with confidence, especially if you have a Forster Co-Ax press.
Tuotenro: 749002538 FORSTER PRODUCTS, INC. UNIVERSAL BULLET PULLER, COLLETS NOT INCLUDED Valmistajan tuotenumero: UP1010757253996863 Forster valmistaa hylsynkaulus-tyylisen luodinpoistajan, joka sopii standardiin seitsemän kahdeksasosaan 14 kierteisiin puristimiin, sekä toisen hylsynkaulus-tyylisen poistajan (molemmat käyttävät samoja Forsterin hylsyjä) Co-Ax puristimelle. FBP1010-poistaja standardipuristimille sisältää hylsyn kiristyskahvan poistajan rungon päällä. FUP1010-poistajassa on yhdeksän kuudettaosaa tuuman kuusikulmainen yläosa poistajan rungossa, joka vaatii avaimen hylsyn kiristykseen. Molemmat poistajat irrottavat helposti luodit lähes mistä tahansa patruunasta. Hylsyt myydään erikseen.
45.9EUR545,90 €
*
Toimitusaika noin 2-4 viikkoa. 5 kpl. USA:n varastossa
Forster valmistaa hylsynkaulus-tyylisen luodinpoistajan, joka sopii standardiin 7/8-14 kierteisiin puristimiin sekä Co-Ax puristimelle.
FBP1010-poistaja sisältää hylsyn kiristyskahvan, kun taas FUP1010-poistajassa on 9/16 tuuman kuusikulmainen yläosa, joka vaatii avaimen hylsyn kiristykseen.
Molemmat poistajat irrottavat helposti luodit lähes mistä tahansa patruunasta, mutta hylsyt myydään erikseen.
Forster makes a collet style bullet puller for standard seven eigths thru 14 threaded presses and a second collet style puller (both use the same Forster collets) for the Co-Ax Press. The FBP1010 puller for standard presses includes a collet tightening handle on top of the puller body. The FUP1010 Puller has a nine sixteenths inch hex top on the puller body which requires a wrench to tighten the collet. Both pullers easily remove bullets from almost any cartridge. Collets are sold separately.
Lisää...
Forster valmistaa hylsynkaulus-tyylisen luodinpoistajan, joka sopii standardiin seitsemän kahdeksasosaan 14 kierteisiin puristimiin, sekä toisen hylsynkaulus-tyylisen poistajan (molemmat käyttävät samoja Forsterin hylsyjä) Co-Ax puristimelle. FBP1010-poistaja standardipuristimille sisältää hylsyn kiristyskahvan poistajan rungon päällä. FUP1010-poistajassa on yhdeksän kuudettaosaa tuuman kuusikulmainen yläosa poistajan rungossa, joka vaatii avaimen hylsyn kiristykseen. Molemmat poistajat irrottavat helposti luodit lähes mistä tahansa patruunasta. Hylsyt myydään erikseen.
Lisää...
Asiakasarviot: FORSTER PRODUCTS, INC. UNIVERSAL BULLET PULLER, COLLETS NOT INCLUDED
Arvioiden lukumäärä: 3
Arvostelut brownells.com sivustolla: 3
Arvioiden keskiarvo: 2,7
Disapointing design(29.1.2012)
I purchased the puller from Sinclair along with three collets, thereby saving money rather than Forster dirctly. The puller I chose was the "Universal" with the hex head as in pic. The hex head is a soft metal nut, thread glued on a minor thread. On the second cartridge (6.5 x 55), the thread lock gave up and the hex head /nut, turned on its own. I am now left with no option but to use padded vice grips to extract the "collet screw body. Why not use a one piece "bolt". Remember the principle of KISS, less to go wrong. The quality of the collets however is high, but the "gripping force" exerted inside the puller by a tapering surface could be better finished, probably such tightening force was required. I would have gone for the Hornady Cam Lock, but, I don`t believe you can cover two calibers with one collet, 6.5/.264 & .257 Also, from Forsters I purchased a dozen pack of die lock rings. I was very disapointed to find them to be soft alloy. Now I happily find Sinclair do their own lock rings in stainless, well done.
Sent it back - would not buy again(15.6.2012)
Not up to the usual Forster quality. The collect nut is held on by lock-tite and came un-screwed on the tenth bullet I pulled. Do not waste your money.
Revised!(29.1.2015)
Product has been revised and now has an allen set screw that appears to be deep enough to seat into (or past) the threads of the collet pusher assembly. No way for the nut to turn now. Simple fix that should have been there from the beginning..., but live and learn. Buy with confidence, especially if you have a Forster Co-Ax press.