Provides increased length and better purchase for faster, easier magazine changes; even with oversized or target-style grips. Easy to install, simply replaces the factory mag release with no permanent alterations to your pistol required.
SPECS: Steel, blued or stainless steel (S/S), matte finish. Fits Ruger Mk II .22 rimfire pistols.
Lisää...
Lisää pituutta helpompiin lippaanvaihtoihin
Tarjoaa lisää pituutta ja paremman otteen nopeampia ja helpompia lippaanvaihtoja varten; jopa ylisuurilla tai kilpatyyppisillä kahvoilla. Helppo asentaa, korvaa vain tehtaan lippaanvapauttimen ilman pysyviä muutoksia pistooliisi.
SPECS: Teräs, sinistetty tai ruostumaton teräs (S/S), mattapinta. Sopii Ruger Mk II .22 reunasytytteisiin pistooleihin.
Arvioiden lukumäärä: 8
Arvostelut brownells.com sivustolla: 8
Arvioiden keskiarvo: 4
great product for the price(16.9.2012)
Read reviews about difficult install.Easiest install you could ask for. Don't remove the spring!!! Take off the grips and remove the pin that holds the latch only. put the new latch in replace and pin. Thats it- 10 minutes tops and it works.
much better than stock(14.7.2018)
five minute install, do NOT remove spring - polished the SS unit to match my mk 2, looks good, works great, good price
A Definate Improvement(23.12.2010)
Let's face it...the factory mag release is the pits! This is a vast improvement in that it sticks out far enough to get a finger under it and it makes magazine changes soooo much easier. I have installed about a dozen of these on my guns and for customers, and never had any problem. Before you remove the old factory magazine release, be sure and make a mental note of how that spring goes in there, or you will be a bit baffled on how to install the new one. Since you are fighting the spring pressure, it is a bit of a trick to get it installed, but not bad.
Not a Drop-In Part(15.4.2011)
Ended up removing this since the magazines won't seat with it. I had to file it down some to allow the magazine in, but is still would not seat properly; would not lock in place. Rather than waste any more time on this I reinstalled the stock part which works just fine.
What was the other reviewer thinking!?(5.3.2012)
This product is the best (and only) accessory I use for the Ruger MK II. I have a few and all of them have Ranch Products releases on them. There are two things this does. First, you don't have to push the release back to insert the magazine like you do for the factory one. Second, it's MUCH easier to push to release the magazine.
Another reviewer made the assertion that their release didn't work and they just sent it back. Huh, six or seven installations later, I'm going to call that assertion bogus.
Good piece(7.6.2012)
First off this was a pain to install. If anyof you have removed the mag release you know how bad it is. But other than that it is a good option, I was thinking the tang would be bigger but I guess it's big enough it won't get stuck on anything but big enough to work well. It is a little skinny for the frame as it has a little lateral movement but nothing to worry about. Overall good product and worth the money.
works on mark 1(11.6.2012)
so i give it 4 stars ONLY because it has no instructions. Now check it out ALL mark 1 users this product works great make sure you study the spring orientation before removing stock release, AND unless you have a gun vise, take down your weapon to install this release. I spent an hour trying to balance the gun and install new release lever, but when i took off the barrel and tried, it took less than a minute.
Excellent results, big difference.(15.4.2013)
I bought this part because I was having a problem with releasing and installing magazines due to my arthritic hands. Installation was easier and quicker than I expected, after reading some of the reviews. I took the grips off and pushed the bottom pin through the frame with a ball point pen. To put it back together, I pushed the new release against the spring and then toward the back of the frame, aligned all the holes and inserted the pin through the frame and the mag release. I had to lightly tap the pin into place with a plastic screwdriver handle.
When I checked for proper function, the empty magazine was hard to insert into the frame and the mag release would not fully close to hold the magazine properly in place. I spread the ears on the mag relese slightly, which allowed the magazine to insert properly into the pistol and lock up tightly. As someone else mentioned, it is not only easier to remove the magazine now, but also easier to insert a fresh magazine into the pistol. Although the release extends lower than the original, I do not expect to have problems with it catching on something and dumping the magazine.
Tuotenro: 746102001 RANCH PRODUCTS EXTENDED MAGAZINE RELEASE, BLUED Valmistajan tuotenumero: NONE Tarjoaa lisää pituutta ja paremman otteen nopeampia ja helpompia lippaanvaihtoja varten; jopa ylisuurilla tai kilpatyyppisillä kahvoilla. Helppo asentaa, korvaa vain tehtaan lippaanvapauttimen ilman pysyviä muutoksia pistooliisi.
34.9EUR4734,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Ominaisuudet:Malli: Mark I, Mark IIMerkki: RugerSuuntaus, kätisyys: CenterViimeistely: Blued
Käsi:
Center
Malli:
Mark I,Mark II
Valmistaja:
Ruger
Viimeistely:
Blued
Toimituksen paino: 0,023kgToimituksen korkeus: 13mmToimituksen leveys: 66mmToimituksen pituus: 89mm
Tuotekuvaus
Made in USA
USA:n vientiluvan tyyppi: 0A501.x
USA:n hallitus kontrolloi näitä tuotteita. Niiden vienti USA:sta on sallittu vain siihen maahan, johon ne on tilattu, ja vain vastaanottajan tai loppukäyttäjän käyttöön. Niitä ei saa uudelleenmyydä, siirtää tai luovuttaa mihinkään muuhun maahan tai muulle henkilölle kuin vastaanottajalle tai loppukäyttäjälle, ei alkuperäisessä muodossaan eikä muiden tuotteiden osana, ilman etukäteen hankittua lupaa USA:n hallitukselta tai muuta USA:n lakiin ja määräyksiin perustuvaa hyväksyntää.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Tuotenro: 746102101 RANCH PRODUCTS EXTENDED MAGAZINE RELEASE, SS Valmistajan tuotenumero: NONE Tarjoaa lisää pituutta ja paremman otteen nopeampia ja helpompia lippaanvaihtoja varten; jopa ylisuurilla tai kilpatyyppisillä kahvoilla. Helppo asentaa, korvaa vain tehtaan lippaanvapauttimen ilman pysyviä muutoksia pistooliisi.
39.9EUR5739,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Ominaisuudet:Malli: Mark I, Mark IIMerkki: RugerSuuntaus, kätisyys: CenterViimeistely: Stainless Steel
Provides increased length and better purchase for faster, easier magazine changes; even with oversized or target-style grips. Easy to install, simply replaces the factory mag release with no permanent alterations to your pistol required.
SPECS: Steel, blued or stainless steel (S/S), matte finish. Fits Ruger Mk II .22 rimfire pistols.
Lisää...
Lisää pituutta helpompiin lippaanvaihtoihin
Tarjoaa lisää pituutta ja paremman otteen nopeampia ja helpompia lippaanvaihtoja varten; jopa ylisuurilla tai kilpatyyppisillä kahvoilla. Helppo asentaa, korvaa vain tehtaan lippaanvapauttimen ilman pysyviä muutoksia pistooliisi.
SPECS: Teräs, sinistetty tai ruostumaton teräs (S/S), mattapinta. Sopii Ruger Mk II .22 reunasytytteisiin pistooleihin.
Arvioiden lukumäärä: 8
Arvostelut brownells.com sivustolla: 8
Arvioiden keskiarvo: 4
great product for the price(16.9.2012)
Read reviews about difficult install.Easiest install you could ask for. Don't remove the spring!!! Take off the grips and remove the pin that holds the latch only. put the new latch in replace and pin. Thats it- 10 minutes tops and it works.
much better than stock(14.7.2018)
five minute install, do NOT remove spring - polished the SS unit to match my mk 2, looks good, works great, good price
A Definate Improvement(23.12.2010)
Let's face it...the factory mag release is the pits! This is a vast improvement in that it sticks out far enough to get a finger under it and it makes magazine changes soooo much easier. I have installed about a dozen of these on my guns and for customers, and never had any problem. Before you remove the old factory magazine release, be sure and make a mental note of how that spring goes in there, or you will be a bit baffled on how to install the new one. Since you are fighting the spring pressure, it is a bit of a trick to get it installed, but not bad.
Not a Drop-In Part(15.4.2011)
Ended up removing this since the magazines won't seat with it. I had to file it down some to allow the magazine in, but is still would not seat properly; would not lock in place. Rather than waste any more time on this I reinstalled the stock part which works just fine.
What was the other reviewer thinking!?(5.3.2012)
This product is the best (and only) accessory I use for the Ruger MK II. I have a few and all of them have Ranch Products releases on them. There are two things this does. First, you don't have to push the release back to insert the magazine like you do for the factory one. Second, it's MUCH easier to push to release the magazine.
Another reviewer made the assertion that their release didn't work and they just sent it back. Huh, six or seven installations later, I'm going to call that assertion bogus.
Good piece(7.6.2012)
First off this was a pain to install. If anyof you have removed the mag release you know how bad it is. But other than that it is a good option, I was thinking the tang would be bigger but I guess it's big enough it won't get stuck on anything but big enough to work well. It is a little skinny for the frame as it has a little lateral movement but nothing to worry about. Overall good product and worth the money.
works on mark 1(11.6.2012)
so i give it 4 stars ONLY because it has no instructions. Now check it out ALL mark 1 users this product works great make sure you study the spring orientation before removing stock release, AND unless you have a gun vise, take down your weapon to install this release. I spent an hour trying to balance the gun and install new release lever, but when i took off the barrel and tried, it took less than a minute.
Excellent results, big difference.(15.4.2013)
I bought this part because I was having a problem with releasing and installing magazines due to my arthritic hands. Installation was easier and quicker than I expected, after reading some of the reviews. I took the grips off and pushed the bottom pin through the frame with a ball point pen. To put it back together, I pushed the new release against the spring and then toward the back of the frame, aligned all the holes and inserted the pin through the frame and the mag release. I had to lightly tap the pin into place with a plastic screwdriver handle.
When I checked for proper function, the empty magazine was hard to insert into the frame and the mag release would not fully close to hold the magazine properly in place. I spread the ears on the mag relese slightly, which allowed the magazine to insert properly into the pistol and lock up tightly. As someone else mentioned, it is not only easier to remove the magazine now, but also easier to insert a fresh magazine into the pistol. Although the release extends lower than the original, I do not expect to have problems with it catching on something and dumping the magazine.
Apu ja yhteydenotto
(0) 
Uutiskirje
Perinteinen näkymä
Mobiilinäkymä