BROWNELLS
BRASS LAPS

050806010062 080499032

For those who want to put on the final touch of perfection. 5°, 11° and 18° brass laps are used with very fine abrasive, which penetrates the brass and works as a final polish to the chamfer cuts.

Lisää...

Niille, jotka haluavat viimeistellä täydellisyyden. 5°, 11° ja 18° messinkiset lapat käytetään erittäin hienon hionta-aineen kanssa, joka tunkeutuu messinkiin ja toimii viimeisenä kiillotuksena viisteiden leikkauksille.

Lisää...

Asiakasarviot: BROWNELLS 32 CALIBER CHAMFERING KIT 11° BRASS LAP

Arvioiden lukumäärä: 1
Arvostelut brownells.com sivustolla: 1
Arvioiden keskiarvo: 5

Used for my Ruger 10/22T recrown (31.7.2010)

The factory crown was rough and eccentric on my 10/22T, so I cut my barrel, polished the new muzzle on a disk sander perfectly smooth and flat, threaded this lap onto my brass cleaning rods (bought at W**Mart), then taped the rod with enough teflon plumber's tape every 4" to barely fit into the barrel (the tape squishes flat as it goes into the bore, so put plenty on), loaded the lap with a little cerium oxide abrasive (used to pitch lap telescope mirrors) mixed with Lucas Red #2 wheel grease (to form a paste) and then attached my cordless drill to the end of the brass rod sticking out of the barrel's breech end. Go slow, check progress often. You want to "just" polish down to the point where the muzzle's lands "almost" touch the grooves. Then use a bit of 1000 grit rouge (also called crocus) cloth wrapped around the tool instead of the abrasive paste to make a 1 or 2 thousands deep "ring" which is barely visible at your muzzle to finish the transition from the barrel lands to groove depth which, if done with care, will give you a better crown than anything money can buy. Go slow, think and shoot straight. The teflon tape around your cleaning rod should keep your bore safe. Be sure not to contaminate the bore with abrasive by only using a paste -- never powdered abrasives by themselves. This process requires hours of work to do it best, but a fine crown is critical to best accuracy if you're a paper puncher. Finish by giving your bore a Brownell's JB Borepaste treatment using first a cleaning brush loaded up for 20 strokes or so, then a cleaning patch with more JB on a tight fitting jag, clean thoughly, oil the bore, patch dry and shoot em up more like the big dollar guns.

Lue 1 arvostelua lisää brownells.com sivustolla

17.9 37.9 8 EUR

Tuotenro: 080499032
BROWNELLS 32 CALIBER CHAMFERING KIT 11° BRASS LAP 050806010062 Niille, jotka haluavat viimeistellä täydellisyyden. 5°, 11° ja 18° messinkiset lapat käytetään erittäin hienon hionta-aineen kanssa, joka tunkeutuu messinkiin ja toimii viimeisenä kiillotuksena viisteiden leikkauksille.

17.9 EUR 0 17,90 € *

Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.

Ominaisuudet: Merkki: Universal Handguns

BROWNELLS BRASS LAPS

Asiakasarviot: BROWNELLS 32 CALIBER CHAMFERING KIT 11° BRASS LAP

Ominaisuudet

Tuotekuvaus

Asiakasarviot: BROWNELLS 32 CALIBER CHAMFERING KIT 11° BRASS LAP

Yhdistä

Turvalliset maksutavat

Ammattijärjestöt

Tervetuloa!

BROWNELLS
BRASS LAPS