EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: CZ 75 CZ 75 SP-01 CZ 75 SP-01 Phantom CZ 75 SP-01 Shadow* CZ 85 CZ 97B CZ 97D CZ P-01 CZ P-07 (may require fitting due to a variance in dovetail dimensions) CZ P-09 (may require fitting due to a variance in dovetail dimensions) CZ PCR (there will be a gap under the front of the adapter plate) Tristar P120
EGW punapisteet on tarkoitettu asennettavaksi vasemmalta oikealle (kiväärin suunta eteenpäin). Liitoskouru on progressiivisesti kapeneva, mikä helpottaa asennusta. Poista vain takatähtäin aseestasi ja vaihda se EGW-tukkiin, jotta voit asentaa Vortex Viper/Venom, Burris FastFire tai Docter punapisteen. Voit poistaa tuen ja vaihtaa takatähtäimen milloin tahansa. Asennusvarusteet mukana. Asennusohjeet Poista takatähtäin* Asenna EGW-tukki liitoskouruun Kiristä asetussiru (jos sovellettavissa) Aseta punapiste EGW-tukille (pienellä paperinpalan asettaminen punapisteen ja tukin väliin helpottaa poistamista ja pitää Loctitea poissa punapisteestä.) Levitä sinistä Loctitea mukana toimitettuihin asennusruuveihin Kiristä asennusruuvit 15in/lbs 2 Painon pääruuvia - toimitettu Vortex Viper ja Venom -pisteille 2 Litteää pääruuvia - toimitettu Burris FastFire ja Docter -pisteille Mukana olevat ruuvit vaativat 5/64'' kuusiokoloavaimen asennukseen. Aseen muokkaaminen voi mitätöidä valmistajan takuun. Tämä tuote tulisi asentaa ja tarkistaa pätevän asekorjaajan toimesta. Valmistaja ei ota vastuuta vahingoista tai vammoista, jotka voivat johtua väärästä asennuksesta tai tämän tuotteen käytöstä. Tämä tuki sopii: CZ 75 CZ 75 SP-01 CZ 75 SP-01 Phantom CZ 75 SP-01 Shadow* CZ 85 CZ 97B CZ 97D CZ P-01 CZ P-07 (voi vaatia sovitusta johtuen liitoskourun mittojen vaihtelusta) CZ P-09 (voi vaatia sovitusta johtuen liitoskourun mittojen vaihtelusta) CZ PCR (adapterilevyn etuosassa on aukko) Tristar P120