Yli 300 000 asiakasta - kiitämme teitä!

Yli 40 000 tuotetta metsästykseen ja ammuntaan

HARRISON DESIGN & CONSULTING
SANDING BLOCK FOR 1911 SLIDE AND FRAME FLATS

100019354
Harrison Design and Consulting have used these 2"x7" aluminum sanding block in their shop for years to be able to level and sand out slide and frame flats to any level of polish that their clients have ordered. They think they work so well, that they wanted to offer them for sale. The clamp plate keeps the abrasive paper pulled taught, while the finger and thumb grooves on the sides help you control and direct the block without tiring you out, trying to keep the paper taught, like on a makeshift sanding block. Harrison Design and Consulting's sanding blocks use a 2" wide piece of sandpaper or 2" wide emory strip. They recommend sheet sandpaper in 9"x11" sheets and then advise you tear it length-wise, procure 3 strips 2" wide, plus another 1" wide strip that you could save for general shoe-shine blending. Harrison Design and Consulting include a loose piece of 2" wide 7" long 40 durometer Buna-N rubber that you can use between the abrasive paper and sanding block at your option. When sanding out flats that are a little wavy and they have roll marks, they normally use the rubber to allow some give in the sandpaper and help it follow the surface, rather than forcing it to level the surface. When you've worn out a piece of paper, tear off those un-used ends and save them for wrapping around sanding sticks and files to sand small surfaces.
94.9 94.9 1 EUR
Tuotenro: 100019354
HARRISON DESIGN & CONSULTING ALUMINUM SANDING BLOCK
Valmistajan tuotenumero: HD-BLOCK
94.9 EUR 0 94,90 € *
Jälkitilaus, toimitusaika n. 4-12 viikkoa USA:n varastosta.

Ominaisuudet

Toimituksen paino: 0,692kg Toimituksen korkeus: 32mm Toimituksen leveys: 57mm Toimituksen pituus: 203mm

Tuotekuvaus

Made in USA

Vastuullinen taloudellinen toimija EU-asetuksen mukaisesti

Brownells Finland Oy
Kutojantie 3
02630 Espoo
Suomi
tiedustelut@brownells.fi




Harrison Designin alumiininen hiontalaatta 1911-slideille ja runkoille. 🛠️ Tehokas ja kestävä työkalu tarkkaan viimeistelyyn.

Harrison Design and Consulting have used these 2"x7" aluminum sanding block in their shop for years to be able to level and sand out slide and frame flats to any level of polish that their clients have ordered. They think they work so well, that they wanted to offer them for sale. The clamp plate keeps the abrasive paper pulled taught, while the finger and thumb grooves on the sides help you control and direct the block without tiring you out, trying to keep the paper taught, like on a makeshift sanding block. Harrison Design and Consulting's sanding blocks use a 2" wide piece of sandpaper or 2" wide emory strip. They recommend sheet sandpaper in 9"x11" sheets and then advise you tear it length-wise, procure 3 strips 2" wide, plus another 1" wide strip that you could save for general shoe-shine blending. Harrison Design and Consulting include a loose piece of 2" wide 7" long 40 durometer Buna-N rubber that you can use between the abrasive paper and sanding block at your option. When sanding out flats that are a little wavy and they have roll marks, they normally use the rubber to allow some give in the sandpaper and help it follow the surface, rather than forcing it to level the surface. When you've worn out a piece of paper, tear off those un-used ends and save them for wrapping around sanding sticks and files to sand small surfaces.
Takaisin alkuun