Fluorescent green, combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with tapered tail to help prevent magazine spring bind and improve reliability.
SPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Remington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.
Lisää...
Fluoresoiva vihreä, taistelutyylisen seuraajan muotoilu, jossa pään projektio, näyttää välittömästi näköaistin tai tuntoaistin avulla, onko latausputki tyhjä. Valmistettu ruostumattomasta, iskunkestävästä ABS-muovista, jonka kapeneva häntä auttaa estämään latausjousen takertumista ja parantaa luotettavuutta.
TEKNISET TIEDOT: Pituus 1.7" (4.5cm), halkaisija .91" (23mm). 12 kaliiperi vain. Sopii Remington 870, 1100 ja muihin satunnaisiin haulikoihin, joissa ei ole detenttejä latausputkessa.
Arvioiden lukumäärä: 8
Arvostelut brownells.com sivustolla: 8
Arvioiden keskiarvo: 3,6
= one less(15.1.2011)
Terrible design! Limits the tube capacity by one round, deforms slightly in the tube and then binds as it moves towards the receiver.
Edgard Villa(20.3.2011)
Will fit some newer Remington 870 only with some minor "Dremel" fitting.
Works great!(16.5.2011)
This works great in my 870. I removed the dimples as I added a mag. tube extension. I have had no issues in several hundred rounds. It is solid and made of a tough plastic, not some brittle cheap feeling material. I am sure it will wear very well. The extended "tail" keeps it aligned properly in the spring. It doesn't limit my capacity of 2 3/4" shells.
Magazine Follower Doesn't Follow(28.10.2011)
This binded in the tube after running a single test round through it. Had to knock it free with a screwdriver. Complete waste of the money; glad there's nothing wrong with my original follower.
Good item(15.1.2012)
Use in my 870, Buying another for my 1100. Hi-vis to see magazine is empty at a glance, and acts as a spring guide when spring is fully compressed. There is a reason why expensive mod. kits/shotguns come with this follower.
pro and con(21.4.2015)
all is good with this follower except for the loss of one round in my extended magazine ( went from 7 plus one to 6 plus one), but i think if i cut and file off about half inch from the tail section of the follower, should get back my seventh round. great color and feel on empty mag.
Magazine tube extension(9.6.2016)
I installed a 5 rd mag extension on my 870 and replaced the factory follower with this. One problem. the back edge was "too sharp" to pass where the detents had been. So, I took my Dremel and ground down the edge at an angle about an eighth of an inch. Works perfectly now!
Love it(21.7.2017)
Nicely priced, the product itself is solid. I have an 870 express mag with dimples still on the tube (4shot), 5 minutes with a rounded file and the follower fell in without issue. Still have plenty of room in the tube and retain 4 shells in the mag.
Tuotenro: 800100004 SCATTERGUN TECHNOLOGY REMINGTON 870 MAGAZINE FOLLOWER, 12 GA. Valmistajan tuotenumero: SGHVF683507710193 Fluoresoiva vihreä, taistelutyylisen seuraajan muotoilu, jossa pään projektio, näyttää välittömästi näköaistin tai tuntoaistin avulla, onko latausputki tyhjä. Valmistettu ruostumattomasta, iskunkestävästä ABS-muovista, jonka kapeneva häntä auttaa estämään latausjousen takertumista ja parantaa luotettavuutta.
19.9EUR1419,90 €
*
Toimitusaika noin 2-4 viikkoa. Yli 10 kpl. USA:n varastossa
Fluorescent green, combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with tapered tail to help prevent magazine spring bind and improve reliability.
SPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Remington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.
Lisää...
Fluoresoiva vihreä, taistelutyylisen seuraajan muotoilu, jossa pään projektio, näyttää välittömästi näköaistin tai tuntoaistin avulla, onko latausputki tyhjä. Valmistettu ruostumattomasta, iskunkestävästä ABS-muovista, jonka kapeneva häntä auttaa estämään latausjousen takertumista ja parantaa luotettavuutta.
TEKNISET TIEDOT: Pituus 1.7" (4.5cm), halkaisija .91" (23mm). 12 kaliiperi vain. Sopii Remington 870, 1100 ja muihin satunnaisiin haulikoihin, joissa ei ole detenttejä latausputkessa.
Arvioiden lukumäärä: 8
Arvostelut brownells.com sivustolla: 8
Arvioiden keskiarvo: 3,6
= one less(15.1.2011)
Terrible design! Limits the tube capacity by one round, deforms slightly in the tube and then binds as it moves towards the receiver.
Edgard Villa(20.3.2011)
Will fit some newer Remington 870 only with some minor "Dremel" fitting.
Works great!(16.5.2011)
This works great in my 870. I removed the dimples as I added a mag. tube extension. I have had no issues in several hundred rounds. It is solid and made of a tough plastic, not some brittle cheap feeling material. I am sure it will wear very well. The extended "tail" keeps it aligned properly in the spring. It doesn't limit my capacity of 2 3/4" shells.
Magazine Follower Doesn't Follow(28.10.2011)
This binded in the tube after running a single test round through it. Had to knock it free with a screwdriver. Complete waste of the money; glad there's nothing wrong with my original follower.
Good item(15.1.2012)
Use in my 870, Buying another for my 1100. Hi-vis to see magazine is empty at a glance, and acts as a spring guide when spring is fully compressed. There is a reason why expensive mod. kits/shotguns come with this follower.
pro and con(21.4.2015)
all is good with this follower except for the loss of one round in my extended magazine ( went from 7 plus one to 6 plus one), but i think if i cut and file off about half inch from the tail section of the follower, should get back my seventh round. great color and feel on empty mag.
Magazine tube extension(9.6.2016)
I installed a 5 rd mag extension on my 870 and replaced the factory follower with this. One problem. the back edge was "too sharp" to pass where the detents had been. So, I took my Dremel and ground down the edge at an angle about an eighth of an inch. Works perfectly now!
Love it(21.7.2017)
Nicely priced, the product itself is solid. I have an 870 express mag with dimples still on the tube (4shot), 5 minutes with a rounded file and the follower fell in without issue. Still have plenty of room in the tube and retain 4 shells in the mag.